SSL 4K G
The whole 4K G channel strip across four pages, learned in Bitwig Studio from the VST3.
Page 1 is input and output: Fader on knob 1, Width and Pan on knobs 2 and 3, then Input Trim, Mic, Impedance, and the low-pass and high-pass filters. Buttons: S/C Listen on 1, Polarity on 4, Pre on 5, Impedance on 6 and Filters in on 7.
Page 2 is the lower three EQ bands: LF gain and frequency, LMF gain, frequency and Q, HMF gain, frequency and Q. Buttons: LF type on 1, EQ colour on 2, EQ in on 3, LMF ÷3 on 4 and HMF x3 on 7.
Page 3: HF gain and frequency on knobs 1 and 2, the compressor's ratio, threshold and release on 3 to 5, and the gate's range, threshold and release on 6 to 8. Buttons: HF type on 1, Dynamics in on 3, compressor fast attack on 5, gate fast attack on 7 and Expander on 8.
Page 4 has one knob: the compressor's wet/dry Mix.
Made in Bitwig Studio with the VST3.
Tested with the device Somebody has run this into the gear it was made for.
Does this work with your Solid State Logic 4K G?
Open ROTO-SETUP with the Roto in PLUGIN mode, then File > Import.
The layout
Page 1
Page 2
Page 3
Page 4
All 40 controls
| Page | Control | Name | Feel |
|---|---|---|---|
| 1 | Knob 1 | Fader level | Smooth |
| 1 | Knob 2 | Width | Center indent |
| 1 | Knob 3 | Pan | Center indent |
| 1 | Knob 4 | Input trim | Center indent |
| 1 | Knob 5 | Mic | Smooth |
| 1 | Knob 6 | Impedance | Smooth |
| 1 | Knob 7 | LP filter | Smooth |
| 1 | Knob 8 | HP filter | Smooth |
| 2 | Knob 1 | LF gain | Center indent |
| 2 | Knob 2 | LF frequency | Center indent |
| 2 | Knob 3 | LMF gain | Center indent |
| 2 | Knob 4 | LMF freq | Center indent |
| 2 | Knob 5 | LMF Q | Center indent |
| 2 | Knob 6 | HMF gain | Center indent |
| 2 | Knob 7 | HMF freq | Center indent |
| 2 | Knob 8 | HMF Q | Center indent |
| 3 | Knob 1 | HF gain | Center indent |
| 3 | Knob 2 | HF freq | Center indent |
| 3 | Knob 3 | Comp ratio | Smooth |
| 3 | Knob 4 | Comp thresh | Smooth |
| 3 | Knob 5 | Comp release | Center indent |
| 3 | Knob 6 | Gate range | Smooth |
| 3 | Knob 7 | Gate thresh | Smooth |
| 3 | Knob 8 | Gate release | Center indent |
| 4 | Knob 1 | Comp mix | Smooth |
| 1 | Button 1 | S/C Listen | Latching |
| 1 | Button 4 | Polarity | Latching |
| 1 | Button 5 | Pre | Latching |
| 1 | Button 6 | Impedance | Latching |
| 1 | Button 7 | Filters | Latching |
| 2 | Button 1 | LF type | Latching |
| 2 | Button 2 | EQ colour | Latching |
| 2 | Button 3 | EQ In | Latching |
| 2 | Button 4 | LMF div3 | Latching |
| 2 | Button 7 | HMF x3 | Latching |
| 3 | Button 1 | HF Type | Latching |
| 3 | Button 3 | Dynamics In | Latching |
| 3 | Button 5 | Cmp fast atk | Latching |
| 3 | Button 7 | GateFastAtk | Latching |
| 3 | Button 8 | Gate Expande | Latching |
Details
- Made for
- Solid State Logic 4K G
- Format
- VST3
- DAW
- Bitwig
- Works with
- Roto-Control
- Panel used
- 25 knobs, 15 buttons, 4 pages
- Firmware tested
- 3.3.0
- Added
- 2026-10-26