Korg minilogue xd
The minilogue xd's synth engine across four pages: both oscillators, the multi engine and mixer, filter and amp envelope, then the mod envelope and LFO.
Ten knobs are stepped with real detents and labels, so oscillator waves read SQR, TRI and SAW, octaves read 16', 8', 4' and 2', and the multi engine reads NOISE, VPM and USR. The two oscillators are labelled V1 and V2 throughout so you always know which one you have hold of.
Page 2 puts the multi engine sub-type and shift-shape on dedicated knobs. On the synth, shift-shape is a SHIFT gesture on the shape knob.
Switches cover sync, ring, the three effects on/off, and a momentary damper.
Every CC is taken from Korg's own MIDI implementation chart. Set the channel to match the synth's, which is channel 1 by default.
Tested on a Roto-Control Loads and behaves correctly on the hardware. It has not been played into the device itself.
Does this work with your Korg minilogue xd?
Open ROTO-SETUP, select the slot you want to overwrite, then File > Import.
Set this to match your gear and we will change it in the file before you download it.
The layout
Page 1
- V1 SQR
- V1 TRI
- V1 SAW
- V1 16'
- V1 8'
- V1 4'
- V1 2'
- V2 SQR
- V2 TRI
- V2 SAW
- V2 16'
- V2 8'
- V2 4'
- V2 2'
Page 2
- NOISE
- VPM
- USR
Page 3
- DRV 0%
- DRV 50%
- DRV 100%
- KEY 0%
- KEY 50%
- KEY 100%
Page 4
- CUTOFF
- PITCH 2
- PITCH
- LFO SQR
- LFO TRI
- LFO SAW
- 1-SHOT
- NORMAL
- BPM
All 38 controls
| Page | Control | Name | Sends | Channel | Feel |
|---|---|---|---|---|---|
| 1 | Knob 1 | VCO1 Wave | CC 50 | 1 | 3 detents: V1 SQR, V1 TRI, V1 SAW |
| 1 | Knob 2 | VCO1 Octave | CC 48 | 1 | 4 detents: V1 16', V1 8', V1 4', V1 2' |
| 1 | Knob 3 | VCO1 Pitch | CC 34 | 1 | Center indent |
| 1 | Knob 4 | VCO1 Shape | CC 36 | 1 | Smooth |
| 1 | Knob 5 | VCO2 Wave | CC 51 | 1 | 3 detents: V2 SQR, V2 TRI, V2 SAW |
| 1 | Knob 6 | VCO2 Octave | CC 49 | 1 | 4 detents: V2 16', V2 8', V2 4', V2 2' |
| 1 | Knob 7 | VCO2 Pitch | CC 35 | 1 | Center indent |
| 1 | Knob 8 | VCO2 Shape | CC 37 | 1 | Smooth |
| 2 | Knob 1 | Multi Type | CC 53 | 1 | 3 detents: NOISE, VPM, USR |
| 2 | Knob 2 | Multi Sub | CC 103 | 1 | Smooth |
| 2 | Knob 3 | Multi Shape | CC 54 | 1 | Smooth |
| 2 | Knob 4 | Shift Shape | CC 104 | 1 | Smooth |
| 2 | Knob 5 | VCO1 Level | CC 39 | 1 | Smooth |
| 2 | Knob 6 | VCO2 Level | CC 40 | 1 | Smooth |
| 2 | Knob 7 | Multi Level | CC 33 | 1 | Smooth |
| 2 | Knob 8 | Cross Mod | CC 41 | 1 | Smooth |
| 3 | Knob 1 | Cutoff | CC 43 | 1 | Smooth |
| 3 | Knob 2 | Resonance | CC 44 | 1 | Smooth |
| 3 | Knob 3 | Drive | CC 84 | 1 | 3 detents: DRV 0%, DRV 50%, DRV 100% |
| 3 | Knob 4 | Keytrack | CC 83 | 1 | 3 detents: KEY 0%, KEY 50%, KEY 100% |
| 3 | Knob 5 | Amp Attack | CC 16 | 1 | Smooth |
| 3 | Knob 6 | Amp Decay | CC 17 | 1 | Smooth |
| 3 | Knob 7 | Amp Sustain | CC 18 | 1 | Smooth |
| 3 | Knob 8 | Amp Release | CC 19 | 1 | Smooth |
| 4 | Knob 1 | EG Attack | CC 20 | 1 | Smooth |
| 4 | Knob 2 | EG Decay | CC 21 | 1 | Smooth |
| 4 | Knob 3 | EG Int | CC 22 | 1 | Center indent |
| 4 | Knob 4 | EG Target | CC 23 | 1 | 3 detents: CUTOFF, PITCH 2, PITCH |
| 4 | Knob 5 | LFO Wave | CC 57 | 1 | 3 detents: LFO SQR, LFO TRI, LFO SAW |
| 4 | Knob 6 | LFO Mode | CC 58 | 1 | 3 detents: 1-SHOT, NORMAL, BPM |
| 4 | Knob 7 | LFO Rate | CC 24 | 1 | Smooth |
| 4 | Knob 8 | LFO Int | CC 26 | 1 | Center indent |
| 1 | Button 1 | Sync | CC 80 | 1 | Latching |
| 1 | Button 2 | Ring | CC 81 | 1 | Latching |
| 1 | Button 3 | Mod FX | CC 92 | 1 | Latching |
| 1 | Button 4 | Delay | CC 94 | 1 | Latching |
| 1 | Button 5 | Reverb | CC 95 | 1 | Latching |
| 1 | Button 6 | Damper | CC 64 | 1 | Momentary |
Details
- Made for
- Korg minilogue xd
- Works with
- Roto-Control
- Panel used
- 32 knobs, 6 buttons, 4 pages
- MIDI channel
- 1
- Firmware tested
- 3.2.0
- Added
- 2026-09-10