Bitwig EQ+
Bitwig's own EQ+ as an eight-band EQ across three pages. Every page uses the same layout: knobs 2 to 4 and 5 to 7 are frequency, gain and Q, and each band's on/off is the button under its frequency knob.
Page 1 is the filters and shelves: high-pass frequency on knob 1 (20 Hz to 1k), the low shelf on 2 to 4 (20 to 500 Hz), the high shelf on 5 to 7 (2k to 20k) and low-pass frequency on 8 (1k to 20k). Page 2 is bells 3 (40 to 800 Hz) and 4 (100 Hz to 2k), page 3 bells 5 (400 Hz to 8k) and 6 (1k to 16k).
Each frequency knob covers only its band's range, scaled to EQ+'s own curve. Gain knobs have a detent at 0 dB, and the shelf and bell frequency knobs at the middle of their range.
Set up EQ+ first. It opens with no bands, and the setup only works once all eight exist, so create these and save them as EQ+'s default preset:
1. Low-cut, 2-pole, 20 Hz, switched off
2. Low shelf, 100 Hz
3. Peak, 180 Hz
4. Peak, 450 Hz
5. Peak, 1.8 kHz
6. Peak, 4 kHz
7. High shelf, 6.3 kHz
8. High-cut, 2-pole, 20 kHz, switched off
At those frequencies every knob starts on its detent and the filters at their end stops.
Made in Bitwig Studio.
Tested with the device Somebody has run this into the gear it was made for.
Does this work with your Bitwig EQ+?
Open ROTO-SETUP with the Roto in PLUGIN mode, then File > Import.
The layout
Page 1
Page 2
Page 3
All 28 controls
| Page | Control | Name | Range | Feel |
|---|---|---|---|---|
| 1 | Knob 1 | Band1 Freq | 0 to 9278 | Smooth |
| 1 | Knob 2 | Band2 Freq | 0 to 7634 | Center indent |
| 1 | Knob 3 | Band 2 Gain | Center indent | |
| 1 | Knob 4 | Band 2 Q | Center indent | |
| 1 | Knob 5 | Band7 Freq | 10922 to 16383 | Center indent |
| 1 | Knob 6 | Band 7 Gain | Center indent | |
| 1 | Knob 7 | Band 7 Q | Center indent | |
| 1 | Knob 8 | Band8 Freq | 9278 to 16383 | Smooth |
| 2 | Knob 2 | Band3 Freq | 1642 to 8749 | Center indent |
| 2 | Knob 3 | Band 3 Gain | Center indent | |
| 2 | Knob 4 | Band 3 Q | Center indent | |
| 2 | Knob 5 | Band4 Freq | 3817 to 10922 | Center indent |
| 2 | Knob 6 | Band 4 Gain | Center indent | |
| 2 | Knob 7 | Band 4 Q | Center indent | |
| 3 | Knob 2 | Band5 Freq | 7105 to 14210 | Center indent |
| 3 | Knob 3 | Band 5 Gain | Center indent | |
| 3 | Knob 4 | Band 5 Q | Center indent | |
| 3 | Knob 5 | Band6 Freq | 9278 to 15854 | Center indent |
| 3 | Knob 6 | Band 6 Gain | Center indent | |
| 3 | Knob 7 | Band 6 Q | Center indent | |
| 1 | Button 1 | Band 1 On | Latching | |
| 1 | Button 2 | Band 2 On | Latching | |
| 1 | Button 5 | Band 7 On | Latching | |
| 1 | Button 8 | Band 8 On | Latching | |
| 2 | Button 2 | Band 3 On | Latching | |
| 2 | Button 5 | Band 4 On | Latching | |
| 3 | Button 2 | Band 5 On | Latching | |
| 3 | Button 5 | Band 6 On | Latching |
Details
- Made for
- Bitwig EQ+
- DAW
- Bitwig
- Works with
- Roto-Control
- Panel used
- 20 knobs, 8 buttons, 3 pages
- Firmware tested
- 3.2.1
- Added
- 2026-10-29